If you’ve ever stood near an airport during a commercial jet’s arrival, you’ve probably noticed the thick, clouds of gray rubber that peel off from a plane’s landing gear tires and streak the runway. For anyone in the aviation supply chain—especially those of us who design, test, and manufacture landing gear components—it’s a question we get almost weekly from airline maintenance teams, MRO (Maintenance, Repair, and Overhaul) providers, and even new engineers just starting out: “Why do landing gear tires wear so much faster than the tires on a car, or even the tires on a plane’s main body?” Landing Gear

As a landing gear supplier with 18 years in the game, I’ve spent thousands of hours in our test labs crunching data, speaking with pilots and fleet maintenance managers, and troubleshooting premature tire failures. The answer isn’t just “they touch the runway every flight”—it’s a combination of design tradeoffs, extreme operational conditions, and a few little-known factors that most people outside the industry don’t think about. Let’s break it down, starting with the basics that even seasoned pros sometimes overlook.
First, let’s set the baseline: a commercial jet’s landing gear tires are not built the same as car tires, or even the tires on a plane’s wing-mounted “auxiliary” tires (a rare, smaller set used for rare operations like ferry flights). A standard Boeing 737 landing gear tire, for example, is a 49 x 17-inch radial tire with a load rating of over 28,000 pounds per tire. Compare that to a typical passenger car tire, which is around 28 x 12 inches and rated for less than 2,000 pounds. But size and load alone don’t explain the wear rate—what matters far more is the energy a landing gear tire absorbs during touchdown, and how that energy translates to friction.
When a car hits a pothole, the suspension absorbs the impact by compressing the shock absorber, spreading the force out over a fraction of a second. Landing gear? Its suspension has a much different job. Let’s think about a widebody jet landing at 150 knots (roughly 172 mph)—that’s not just speed, that’s a huge amount of kinetic energy. The landing gear’s oleo strut (the large, shock-absorbing cylinder you see on most jets) is designed to compress quickly to dissipate that energy, but the tire itself still takes a massive hit. During touchdown, the tire isn’t just rolling onto the runway—it’s slamming into it. The vertical impact of landing creates a force that can be 2 to 3 times the weight of the plane, distributed over the tire’s contact patch. Every time that happens, the rubber flexes, deforms, and then snaps back. Over hundreds of landings a month, that constant flex fatigues the rubber at the molecular level—think of bending a paperclip back and forth until it breaks. But that’s only part of the story.
Then there’s ground speed and braking dynamics. When a car brakes, it decelerates smoothly because the tire is already rolling at a speed close to the car’s. A jet’s landing gear tires, though, have to spin up from a dead stop (or close to it) in milliseconds to match the plane’s ground speed at touchdown. That spin-up creates a tremendous amount of skid friction—more friction, in fact, than most car tires ever experience in their entire life cycle. Airlines might think of tire wear as just tread loss, but skid-induced wear is the biggest culprit here. I’ve seen data from a Delta Air Lines fleet that shows 60% of their landing gear tire tread loss comes from that initial spin-up skid, not from braking during taxi or high-speed stop-and-go operations. What’s worse: if a pilot has a “hard landing”—a common event that’s not necessarily dangerous, just a sharper-than-usual touchdown—that spin-up skid becomes even more intense. We tested this in our lab last year: a single hard landing adds the equivalent wear of 10 normal landings to a set of landing gear tires.
Another factor that’s easy to miss: the environment in which landing gear operates, both on the ground and in the air. Unlike car tires, which spend almost all their life on paved roads, landing gear tires are often exposed to runway debris, de-icing fluids, and extreme temperature swings. Runways are covered in rubber shavings from previous landings, dirt, small pebbles, and even fragments of plane parts after minor incidents. When a tire rolls over this debris, sharp fragments can cut into the rubber, creating small tears that grow over time. De-icing fluids, which are sprayed on runways in cold climates, are highly corrosive to rubber compounds. We’ve seen tires that spent just six months operating out of a Canadian airport develop 30% more tread loss than identical tires operating out of a dry, warm airport in Florida, just because of the constant exposure to de-icing glycols.
Temperature is another big one. Landing gear tires operate in two extremes: in the air, at 35,000 feet, temperatures can drop to -55°C (-67°F), and on the ground during high-speed taxi and braking, tire temperatures can climb to over 150°C (302°F) from friction. Rubber’s performance drops off sharply outside its optimal temperature range—when it’s too cold, it becomes brittle and cracks easily; when it’s too hot, it softens and wears away faster. The constant swing between cold and hot, which a car tire rarely experiences (even highway driving doesn’t drop a tire to -50°F), makes the rubber far more prone to wear. I remember a test we did in 2021 where we kept a set of test tires in a temperature chamber cycling between -40°C and 120°C. After just 500 cycles, the tire’s tread wear was 40% higher than a control set kept at a constant 20°C.
Wait, but what about other plane tires? Why don’t the tires on the nose gear wear as fast, for example? That’s a question I get all the time. Nose gear tires are smaller, carry much less load, and only handle about 10% of the plane’s total weight. Their touchdown force is also lower, because the nose gear touches down after the main gear, when the plane is already pitched up slightly and decelerating a bit. So their wear rate is roughly a third of main landing gear tires, which aligns with the numbers we see in MRO logs. Even the auxiliary tires I mentioned earlier—used only for rare ferry flights when a main gear tire fails—are built for low wear because they only touch the runway a handful of times. It all comes back to load, impact, and how often the tire is stressed.
Another less talked-about point: regulatory requirements. Airlines need landing gear tires that are lightweight enough to not add unnecessary weight to the plane (which hurts fuel efficiency) but strong enough to handle all those stresses. It’s a constant tradeoff for suppliers like us: if we make a tire thicker and more durable, we add weight, which costs the airline thousands of dollars a year in fuel. If we make it lighter, it doesn’t last as long. So the tire you’re seeing on the runway after every landing is a compromise between weight, strength, and wear. That compromise is why they wear faster than you might expect—there’s no way around it, given how airlines balance operational costs and safety.
I’ve seen this tradeoff play out firsthand in our work. A few years ago, a major European airline came to us asking for a tire that would last 20% longer than their current offering. We spent 18 months developing a new rubber compound with a higher silica content, which improved tread resistance to abrasion. But when we tested it, we found the new compound was heavier, adding 12 pounds per tire. That might sound small, but for a fleet of 50 A320s, that’s 1,200 pounds of extra weight—enough to cost the airline an extra $2 million a year in fuel. We had to scale back the compound to keep weight low, which meant the wear improvement was only 10%, not 20%. That’s the kind of tradeoff that defines landing gear tire design, and it’s why wear rates are as high as they are.
Now, you might be wondering: what does this all mean for fleet managers and maintenance teams? For one, understanding these factors can help you reduce premature wear. Simple steps like limiting hard landings (pilots can be trained to smooth touchdown, which cuts spin-up skid by almost 50%), inspecting tires for debris after each flight, and adjusting de-icing fluid application to minimize exposure to tires can make a big difference. For suppliers like us, it means investing in better testing—we’re currently building a new test lab that can simulate 100 landings an hour, 24/7, with temperature and debris controls, to get more accurate data on wear rates.
If you’re an airline MRO, fleet operator, or anyone involved in landing gear maintenance, you know that tire wear is a constant cost. At our company, we don’t just supply tires—we work with you to analyze your fleet’s operational data to identify exactly what’s driving your wear rate, whether it’s hard landings, environmental exposure, or design compromises. We can help you optimize tire changes, reduce unplanned maintenance, and lower your overall costs without sacrificing safety.

If you’re ready to talk about how we can support your landing gear needs, don’t hesitate to reach out. Whether you’re looking for more durable tires, wear analysis, or custom solutions for your fleet, we’re here to help.
Light Truck References
- Federal Aviation Administration (FAA). “Landing Gear Tire Wear and Failure Analysis.” Advisory Circular 25.721-1, 2019.
- SAE International. “Aerospace Landing Gear Tire Performance Standards.” AS8047B, 2022.
- Boeing Commercial Airplanes. “Main Landing Gear Operational Characteristics.” Aircraft Systems Engineering Report, 2021.
- International Air Transport Association (IATA). “Aircraft Maintenance Cost Benchmarking: Landing Gear Tires,” 2023.
Owin Vehicles Co., Ltd.
As one of the most professional landing gear manufacturers and suppliers in China, we also support customized service. With abundant experience, we warmly welcome you to wholesale advanced landing gear for sale here from our factory. Quality products and low price are available.
Address: Room 2428, Building 3, Aosheng Building, Licheng District, Jinan City, Shandong Province
E-mail: Owinvehicle@163.com
WebSite: https://www.owintrailer.com/