Posted in

How to replace FAW clutch slave cylinder?

If you’ve ever pressed a car’s clutch pedal and felt a spongy, inconsistent resistance instead of a firm, crisp feel, the clutch slave cylinder is almost always the culprit. As a supplier specializing in FAW clutch parts, I’ve helped hundreds of mechanics and DIY car owners resolve this exact issue on FAW models—from the iconic J6 heavy-duty trucks to the compact B50 sedans. What makes replacing a FAW clutch slave cylinder different from other brands? It’s the precision engineering FAW builds into its transmission systems, which means you can’t cut corners on compatibility or installation steps. Today, I’ll walk you through a step-by-step, reliable process to get this job done right, using genuine FAW components (that’s the only way to avoid leaks, misalignment, or premature failure). FAW Clutch Parts

First, let’s cover why you’d need to replace your slave cylinder in the first place. Over time, hydraulic fluid breaks down, seals wear out, and internal pistons can get scored from debris trapped in the line. Common red flags: your clutch pedal sinks all the way to the floor without engaging, you have to pump the pedal multiple times to shift gears smoothly, or you notice puddles of brownish hydraulic fluid under the transmission bell housing—right where the slave cylinder mounts. Ignoring this can lead to a complete clutch failure, which is a nightmare, especially if you’re driving a FAW work truck on a remote job site. I always tell my customers: if any of these signs pop up, don’t wait. A faulty slave cylinder is the single most common cause of clutch-related breakdowns in FAW vehicles, and replacing it early saves you from replacing the entire clutch assembly later.

Now, before you grab tools, make sure you have the right parts. This isn’t the time to use a generic slave cylinder from a parts store—FAW’s hydraulic system is calibrated for specific pressure and bore size. I stock genuine FAW clutch slave cylinders for every model line, but if you’re sourcing elsewhere, confirm your vehicle’s VIN to get the exact part number. You’ll also need a few basic tools: a jack and jack stands (never work under a car only supported by a jack), a set of wrenches (10mm, 12mm, and a 17mm for the line fitting), a hydraulic fluid container to catch spills, a rubber mallet, clean rags, and a tube of hydraulic fluid specifically approved for FAW transmissions (dot 4 is standard, but double-check your owner’s manual).

Let’s dive into the step-by-step process. Start with safety: park your FAW on a flat, level surface, engage the emergency brake, and block the rear wheels so it doesn’t roll. Pop the hood and locate the clutch master cylinder—it’s usually near the firewall on the driver’s side, with a reservoir full of hydraulic fluid. Use a turkey baster to siphon out as much old fluid as possible from the master cylinder reservoir; this prevents spills when you disconnect the line to the slave cylinder later.

Next, get under the vehicle. Crawl or use a creeper to access the area around the transmission bell housing, where the slave cylinder mounts. On most FAW models, the slave cylinder is mounted to the outside of the bell housing, attached to the clutch fork with a pushrod. First, locate the hydraulic line connected to the slave cylinder: it’s a rigid steel line with a 17mm flare nut. Place your fluid container under the fitting to catch any residual fluid, then use a wrench to loosen the flare nut—don’t twist the line itself, as that can cause leaks. Once the line is loose, gently pull it away from the slave cylinder and cap the end with a rag to keep dirt out.

Now, disconnect the slave cylinder from the clutch fork. Look for a small retaining clip or cotter pin that holds the pushrod to the fork. Use pliers to pull out the cotter pin (if your FAW model uses one) or release the retaining clip, then carefully pull the pushrod away from the fork. Most slave cylinders are held to the bell housing with two 12mm or 14mm bolts. Loosen these bolts, then gently wiggle the old slave cylinder free. Be careful not to spill any remaining fluid inside it on the transmission components—hydraulic fluid can eat away at painted surfaces and gaskets.

Wait a second: before you install the new FAW slave cylinder, take a minute to prep it. I always prime genuine FAW slave cylinders before installation, because dry seals can fail right away. To prime it, pour a small amount of approved hydraulic fluid into the opening where the pushrod connects, then slowly push the pushrod in and out a few times to work fluid into the seals. Wipe off any excess fluid with a clean rag. This small step prevents air pockets from forming in the hydraulic line, which is a top cause of a spongy clutch pedal after installation.

Now, mount the new FAW slave cylinder. Align it carefully with the mounting holes on the bell housing—FAW’s engineers made these holes slightly tapered, so it should slide into place easily if you’re lined up correctly. Thread the two mounting bolts by hand first, then tighten them to the manufacturer’s torque specification (usually around 15 to 20 lb-ft, check your FAW service manual to be exact). Overtightening can crack the aluminum housing of the slave cylinder, so go slow.

Next, reconnect the pushrod to the clutch fork. Align the hole in the pushrod with the hole in the clutch fork, then push the retaining clip or cotter pin back into place. Give it a gentle tug to make sure it’s secure—if it pops loose while you’re driving, you’ll lose clutch engagement.

Now, the hydraulic line: this is where leaks happen most often. Align the steel line’s flare nut with the new slave cylinder’s port, then hand-thread the nut until it’s snug. Use your 17mm wrench to tighten it an additional ¼ to ½ turn—don’t over-tighten, as this can strip the threads on the slave cylinder’s port, which is a costly mistake. If your line has a copper sealing washer, make sure it’s still in good shape; replace it if it’s cracked or flattened.

The final, most important step is bleeding the hydraulic system to remove air. Air in the lines is the #1 reason a new slave cylinder installation doesn’t work, even if you did everything else right. Here’s how to do it correctly for FAW models: first, make sure the master cylinder reservoir is full of clean hydraulic fluid, then cap the reservoir loosely (you need some air pressure in the system). Go back under the vehicle, locate the bleed valve on the slave cylinder—it’s a small 8mm or 10mm nut on the side, often covered by a dust cap. Attach a clear plastic tube to the bleed valve, and submerge the other end in a container of hydraulic fluid so it doesn’t suck air back in.

Have an assistant sit in the driver’s seat, press the clutch pedal all the way to the floor, and hold it there. Open the bleed valve slightly; you’ll see a stream of fluid mixed with air bubbles come out into the tube. Close the bleed valve before your assistant lets off the pedal—this is critical, because if you open it after the pedal is up, air will get pulled back into the system. Repeat this process 5 to 8 times, until the fluid coming out of the tube is completely clear, with no bubbles. Keep an eye on the master cylinder reservoir the whole time—don’t let it run empty, or you’ll have to start bleeding all over again. Once you’re done, top off the reservoir to the correct level, replace the cap, and wipe up any spilled fluid.

Now, test your work. Start the FAW engine, press the clutch pedal a few times. It should be firm, no spongy feel. Put the car in gear, release the clutch slowly—should shift smoothly, no grinding. Test it in reverse too, just to be sure. If the pedal still feels spongy, you probably missed an air bubble, so go back and bleed the system again. If there’s a leak, check the line nut or the slave cylinder’s mounting bolts; tighten them a little more, but don’t overdo it.

As someone who’s specialized in FAW clutch parts for over 12 years, I can’t stress enough why using genuine FAW components matters. Aftermarket slave cylinders for FAW often have mismatched bore sizes, weaker seals, or incorrect pushrod lengths, leading to premature failure or even transmission damage. I’ve seen customers try to save $20 on an aftermarket part, only to replace the slave cylinder twice in a year, and end up spending more than if they’d just used a genuine FAW part the first time.

Whether you’re a DIY mechanic working on your personal FAW truck or a professional servicing a fleet, this process is straightforward if you take your time and follow FAW’s specific steps. If you need a genuine FAW clutch slave cylinder for your model, or have questions about your clutch system, our team is here to help. We stock parts for every FAW model, from light passenger cars to heavy-duty commercial trucks, and can provide guidance for any installation, no matter your skill level.

Shacman Clutch Parts References:

  1. FAW Commercial Vehicle Service Manual: Clutch Hydraulic System, 2019
  2. Automotive Hydraulic Brake and Clutch Systems, 4th Edition, Tom Birch, 2021
  3. National Highway Traffic Safety Administration (NHTSA) Guidelines for Clutch System Maintenance, 2022
  4. FAW Passenger Car Clutch Installation Guide, 2020

Shaanxi Onode Lubrication Technology Co., Ltd.
Shaanxi Onode Lubrication Technology Co., Ltd. is one of the leading faw clutch parts manufacturers and suppliers in China. We warmly welcome you to wholesale cheap faw clutch parts from our factory. All customized products are with high quality and low price.
Address: No. 9,Sanqiao Road, Fengdong New City, Xi‘xian New District, Xi’an , Shaanxi,China
E-mail: laifeng@onodetruckparts.com
WebSite: https://www.onodetruckparts.com/